Loading...
Loading...
All product recalls associated with LUK.
Total Recalls
7
Past Year
0
Class I (Serious)
0
Most Recent
May 2018
Data from FDA, USDA, CPSC, and NHTSA public records. Recall counts vary by company size, industry, and reporting practices. Always check official sources for current information.
LuK GmbH & Co. KG (LuK) has submitted a Defect Information Report based upon decisions made by Kia Motors America and Hyundai Motor America to conduct recalls (numbers 18V257 and 18V260 respectively) to inspect and replace the Hydraulic Clutch Actuator (HCA) caps and assembly that can allow oil to accumulate in the cap area, possibly resulting in an electrical short.
The Fluke voltage testers look like a pen with a yellow, white and gray body. The testers measure 90 to 1000 volts alternating current (VAC). "Fluke" and the model number are printed on the front of each unit. The recall involves Fluke 1AC-A1-I VoltAlert® tester with the following model and item numbers: Product Marking Description 1AC-AI FLUKE-1AC-I VoltAlert Voltage Tester
This recall involves Fluke Digital Clamp Meters with model and serial numbers listed below. The model number may be followed by an "A." Model No. Starting With Serial No. Starting with Serial No. Ending In 333 97010000 98880240 334 97010000 98870101 335 97010000 98860104 336 96220000 98900400 337 96070000 98890607 Serial numbers that begin with "S" or are followed by "R" are not included in the recall. "Fluke" and the model number are printed on the front of the unit and the serial number on the back. The instrument body is yellow, red, and black. The clamp meters measure 0 to 600 volts alternating current (VAC), 0 to 600 volts direct current (VDC) and 0 to 400, 600 or 1000 amps alternating current.
The recalled test leads are red and black with no permanent probes attached. They have the Fluke logo on the connector ends. They were sold individually, as well as with a variety of Fluke multimeters and accessory kits. The recall includes only Fluke Model TL221, TL222 and TL224 test leads. The model numbers are not written on the test leads, but are written on the packaging or on product documents. The recall does not include Fluke test leads with permanently attached test probes, and does not include test leads with a SureGrip™ symbol, shown below, either on a tag around the silicon wire or molded onto the connector end. Fluke test leads with a SureGrip™ symbol are not included in the recall.
Multimeters are used to measure voltage, resistance and current. The recalled Fluke digital multimeters measure up to 1,000 volts alternating current (VAC) and direct current (VDC). "Fluke" and "175", "177" or "179" are written on the front of the unit. The tester body is yellow and black, and measures about 7.25 inches long by 3.5 inches wide. Recalled units have a serial number below 79000000. The serial number is written on the back of the instrument, under the hinged stand.
Fluke Corp. Recall of Electrical Testers Recall Alert U.S. Consumer Product Safety Commission Office of Information and Public Affairs Washington, DC 20207 June 19, 2001 Alert #01-515 CPSC, Fluke Corp. Announce Recall of Electrical Testers PRODUCT: - Electrical Testers - Fluke Corp., of Everett, Wash., is voluntarily recalling approximately 33,000 model T-2 hand-held electrical voltage and continuity testers. These testers measure 24 to 600 volts alternating current (VAC), and 6 to 220 volts direct current (VDC). "Fluke" and "T2" are written on the front of the unit. The tester body is yellow and black, and measures about 6.25 inches long by 1.75 inches wide and 1.25 inches thick. The wire leads are black and have one black and one red probe. Recalled units have a serial number higher than 73510000. The serial number is located on the back of the unit above the wire leads. Home centers, hardware stores and industrial distributors nationwide sold these testers between June 1999 and March 2001 for about $49. PROBLEM: The recalled units can "lock-up" and stop working. When the tester "locks-up" it stops working for approximately 8 minutes without warning. Consumers testing electrical sources could fail to be warned of the presence of live current if the tester is not properly operating, posing a risk of shock, electrocution, and thermal burns. Fluke conducted two previous recalls in November 1998 and 1999 on T2 Electrical Testers because of different electrical connection problems. Even if consumers had their testers repaired previously (serial numbers below 74165430), their testers could be part of this new recall and the serial number must be checked to determine if it is included in this recall program. INCIDENTS/INJURIES: Fluke has received one report of a tester that "locked-up" and stopped working. No injuries have been reported. WHAT TO DO: Consumers should stop using these voltage and continuity testers immediately, and contact Fluke for information on returning the recalled unit to Fluke for a free repair. Consumers should call Fluke toll-free at (800) 753-8646 between 5 a.m. and 4 p.m. PT Monday through Friday. Consumers can access Fluke's web site at www.fluke.com/t2recall. Fluke has sent direct notice to known purchasers.
Electrical Testers Recalled by Fluke NEWS from CPSC U.S. Consumer Product Safety Commission Office of Information and Public Affairs Washington, DC 20207 FOR IMMEDIATE RELEASE November 9, 1999 Release # 00-014 Company Phone Number: (800) 753-8646 CPSC Consumer Hotline: (800) 638-2772 CPSC Media Contact: Ken Giles, (301) 504-7052 CPSC, Fluke Corp. Announce Second Recall of Electrical Testers WASHINGTON, D.C. - In cooperation with the U.S. Consumer Product Safety Commission (CPSC), Fluke Corp., of Everett, Wash., is voluntarily recalling about 58,000 model T-2 hand-held electrical voltage and continuity testers. The batteries in the tester could fail to maintain proper contact due to corrosion within the battery compartment, causing the device to lose power. Consumers testing electrical sources could fail to be warned of the presence of live current if the tester is not powered, posing a risk of shock, electrocution, and thermal burns. Fluke conducted a previous recall in November 1998 on T2 Electrical Testers because of a different electrical connection problem. Even if consumers had their testers repaired previously, their testers are part of this new recall and need to be repaired again. Fluke is aware of two incidents involving these testers where consumers received a mild electric shock. These testers measure 24 to 600 volts alternating current (VAC), and 6 to 220 volts direct current (VDC). "Fluke" and "T2" are written on the front of the unit. The tester body is yellow and black, and measures about 6.25 inches long by 1.75 inches wide and 1.25 inches thick. The wire leads are black and have one black and one red probe. Recalled units have a serial number lower than 74165430. The serial number is located on the back of the unit above the wire leads. Home centers, hardware stores and industrial distributors nationwide sold these testers between December 1997 and September 1999 for about $45. Consumers should stop using these voltage and continuity testers immediately, and contact Fluke to obtain a free repair kit or arrange to send your unit to Fluke for repair. For information on returning your unit to Fluke or obtaining a repair kit, consumers should call Fluke toll-free at (800) 753-8646 between between 5 a.m. and 4 p.m. PT Monday through Friday. Consumers can access Fluke's web site at www.fluke.com/whatsnew/ProductNotices/notices_99-10-01.asp.